|
|
OmniTurn Cutting Tools
|
|
|
|
|
|
|
|
|
|
Dual Large MB Holder
Dual Large MB holder
Uses right handed inserts
|
Extra T-25 wrench
|
Extra 4.67-127 screw. Sold in
packs of (10)
|
|
|
1/2" shank square tool holder
STANR-085-V Right hand
|
Extra T-25 wrench
|
Extra 4.76-127 screw. Sold in
packs of (10)
|
|
|
|
|
Inserts
Front Turning -
Cut Off - Threading -
Back Turning - Grooving -
Plunge & Turn
|
|
|
|
|
• Larger inserts are available for use with a square shank
holder and Double holder. The inserts will take heavier and
deeper cuts. These holders and inserts are best held with the
OmniPost-W.
• The tool is held off the face of the tooling plate with
the OmniPost and holder. This enables longer turns and
“back” work.
• The inserts are very cost competitive. They have three
cutting edges, so the cost of the insert is not much more
than the other “standard” inserts.
Insert price notes:
• C-2 or C-5 grade carbides are available.
C-2 will be supplied unless C-5 is requested.
• Prices quoted are for coated inserts. Uncoated inserts
are available
• Inserts shown are right handed. Left handed inserts and
holders are also stocked.
|
|
|
|
Inserts for Starter Kits
(1) Front turn TFTRB-5045
(2) Front turn
TFTR-5040
(1) Back turn
TBTR-5308
(1) Cut off TCOR-5156
(1) Cut off TCOR-5155
(1) Groove .062”
TNGR-5062
(1) Threading
TNVR-5093
(1) Threading
TNVR-5047
(1) Plunge and Turn
TTGR-5093
(1) Spare screw
4,76-127
|
|
|
|
|
|
|
|
|
|
|
Front turn
Sold in packs of (10),
* Notes chip breaker is ground on top edge
Insert #
|
Width
|
D
|
R
|
TFTR-5040
|
.25
|
.44”
|
.000
|
TFTR-5045
|
.25
|
.44”
|
.005
|
TFTRB-5040*
|
.25
|
.44”
|
.000
|
TFTRB-5045*
|
.25
|
.44”
|
.005
|
|
|
|
|
|
Cut off
Sold in packs of (10),
Insert #
|
Width
|
D
|
R
|
TCOR-51510
|
.156
|
.44”
|
15
|
TCOR-5158
|
.125
|
.44”
|
15
|
TCOR-5156
|
.093
|
.44”
|
15
|
TCOR-5155
|
.078
|
.37”
|
15
|
TCOR-5154
|
.062
|
.30”
|
15
|
TCOR-5153
|
.047
|
.23”
|
15
|
TCOR-5201M
|
.040
|
.18”
|
20
|
|
|
|
|
|
Threading 60 degree
Sold in packs of (10),
Thread form is centrally located
Insert #
|
Width
|
D
|
R
|
TNVR-5125
|
.125
|
.44”
|
.004
|
TNVR-5093
|
.093
|
.37”
|
.004
|
TNVR-5047
|
.047
|
.25”
|
.000
|
|
|
|
|
|
Back turn
Sold in packs of (10),
Insert #
|
Width
|
D
|
R
|
TBTR-53010
|
.156
|
.44”
|
.000
|
TBTR-5308
|
.125
|
.44”
|
.000
|
TBTR-5306
|
.093
|
.37”
|
.000
|
TBTR-5305
|
.078
|
.30”
|
.000
|
TBTR-5304
|
.062
|
.23”
|
.000
|
|
|
|
|
|
Grooving
Sold in packs of (10),
Insert #
|
Width
|
D
|
R
|
TNGR-5156
|
.156
|
.44”
|
.000
|
TNGR-5125
|
.125
|
.44”
|
.000
|
TNGR-5093
|
.093
|
.37”
|
.000
|
TNGR-5078
|
.078
|
.37”
|
.000
|
TNGR-5062
|
.062
|
.30”
|
.000
|
TNGR-5047
|
.047
|
.23”
|
.000
|
TNGR-5040
|
.040
|
.18”
|
.000
|
|
|
|
|
|
Plunge & Turn
Sold in packs of (10),
Insert #
|
Width
|
D
|
R
|
TTGR-5156
|
.156
|
.44”
|
.000
|
TTGR-5125
|
.125
|
.44”
|
.000
|
TTGR-5093
|
.093
|
.37”
|
.000
|
TTGR-5078
|
.078
|
.30”
|
.000
|
TTGR-5062
|
.062
|
.23”
|
.000
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|