¢ Axis motor and amplifier issues

• Axis not moving | Axis not repeating

• Tuning AMC Amps

• Axis Servo Errors

• Tuning Copley Amps

• Ctrl-H / Ctrl-C test

• Tuning OmniTurn amps

• Motion Control Issues

• Tuning OmniTurn gold amps

• VIDEO: Balancing gold amplifiers in G35 & older controls

¢ Barfeed issues

• Pneumatic bar feed installation notes

¢ Collet Closer

• Dunham type issues

• What type of collet closer do you have?

• Taming the Dunham Collet Closer

¢ Control issues

• Adjusting RPMs

• MC2 Card modification doc

• Ctrl-H / Ctrl-C test

• Motherboard beeps

• Disassembly of G2 & G3 controls

• Motherboard Installation

• Disk failure / Disk not found

• Password procedure

• DOS notes

• "Polling Controller" message

• Floppy to USB Converter

• Replacing Epia ML Motherboard with Epia M830

• Installing an OmniTurn Hard Drive

• RS232 File Transfer

• Locking up issues

• Spindle encoder troubleshooting

• M function Diagnostic console

• Mathematic Calculations

¢ G4 control issues

• G4 Password protection

• Installing G4 Control on Yaskawa C-Axis

• G4 Thumb drive

• Restoring hard drive on G4 control

• G4 Software revision history updates

• Setting Metric mode as default

• Honing: when honing the motor does not hone in one revolution of the ballscrew

• Software (Accumulative) 
  Updates for G4 Control

• Installing G4 Control on an Inverter Machine

• To set up hard drive on G4 CNC

• Replacing Epia ML Motherboard with Epia M830

• Retrofit installation instructions

¢ Machining issues

• Bad finish problems

• Threading problems

• Holding size problems

¢ Manuals

• OmnITurn Manual - English

• G3 Owner's Manual

• OmniTurn Manual - Spanish (G2 & G3)

• G4 Owner's Manual (TB1)

• OmniTurn Training Manual

• G4 Owner's Manual (CCA)

• OmniTurn - Trouble shooting guide

• OmniTurn PM checklist

¢ Mechanical issues

• Adjusting the height of center on GT & Attachment

• Checking the height of center of a tooling plate

¢ Off line and office computer issues

• Configuring NotePad as your off line editor

• Removing .txt extensions from program files

• DOS notes and commands

• Using standard word processors off line

¢ Programming issues

• Fanuc programmer notes

• Programming work sheet

• Programming help

• VIDEO - Saving part programs in Windows 7

¢ Service and maintenance

• Baco to Allen Bradley jog switch

• PM maintenance list

• Maintenance description

• Replacing Work Lamp on GT-75

• Maintenance & Lubrication Schedule
  for GT-75 & GT-Jr

• Spindle bearing replacement

• OmniTurn Operator and Maintenance Manual

• Universal grease gun

¢ Spindle drive issues

• Adjusting RPMs

• Spindle repair procedure

• Analog Spindle Inverter problems (mrw)

• Yaskawa AC Drive-V1000

• Balance M19 Card

• Yaskawa Drive-GPD 315/V7

• C axis Baumuller Tech Notes

• Yaskawa GPD315 inverter diagram & photo

• C axis drive

• Yaskawa Mini 2 hp parameters & wiring

• C axis spindle drive prints - Indermat version

• Yaskawa Parameters for 5hp & 2hp PC3 Inverters

• GPD 315 simple parameter setting doc

• Yaskawa PC3 inverter PDF 1.4 meg

• Installing a HSL spindle drive

• Yaskawa Update Disk

• Setting Mitsubishi inverter parameters - 1997

¢ Suhner info

• BEWI-6 spindle print